Pfeiffer HiPace 1200 turbomolecular high-vacuum pumps with an ISO-F 200 inlet flange have a pumping speed of 1300 liters per second (l/s), and an ultimate pressure of 7.5 x 10 Torr. This Pfeiffer HiPace 1200 pump comes with an integrated TC 1200 drive unit mounted underneath the pump and has an ISO KF-40 exhaust foreline flange. The pump can be mounted from vertical (high-vacuum flange on top) to 90° (horizontal). Input power of 100 - 120/200 - 240 VAC 50/60 at a maximum of 1300 Watts is supplied directly to the TC1200 drive unit which powers the pump. The required AC power cable (not included) is part number P1012627. This HiPace 1200 turbo pump with ISO-F 200 inlet and TC 1200 drive unit comes standard with a water-cooling kit and has Pfeiffer part number: PM P06 001.

Pfeiffer HiPace 1200 turbomolecular high-vacuum pumps with a DN200 Conflat CF 10.0 inch inlet flange have a pumping speed of 1300 liters per second (l/s), and an ultimate pressure of 3.5 x 10 Torr. This Pfeiffer HiPace 1200 pump comes with an integrated TC 1200 drive unit mounted underneath the pump and has an ISO KF-40 exhaust foreline flange. The pump can be mounted from vertical (high-vacuum flange on top) to 90° (horizontal). Input power of 100 - 120/200 - 240 VAC 50/60 at a maximum of 1300 Watts is supplied directly to the TC1200 drive unit which powers the pump. The required AC power cable (not included) is part number P1012627. This HiPace 1200 turbo pump with CF 10.0" inlet and TC 1200 drive unit comes standard with a water-cooling kit and has Pfeiffer part number: PM P06 002.

The Pfeiffer OmniControl 001 turbo pump controller can be bench top or rack mounted and is designed to operate the larger Pfeiffer HiPace 1200 turbo pumps that have the integrated TC 1200 electronic drive unit. The OmniControl 001 drive unit is powered by the pump and does not have a built in power supply. The HiPace 1200 turbo pump has its own onboard 48 VDC power supply and takes direct input power of 115/230 VAC. Since it does not have its own power supply, the OmniControl 001 is very compact and has Pfeiffer part number PE D40 100 0. The OmniControl 001 can control all the main parameters of the HiPace turbo pump via a 3 meter long RS485 interface cable (part number P1012287, not included). This unit can also be used to operate and display pressure readings from Pfeiffer Active gauges if the optional Gauge/IO module is installed.

This input power supply power cord (mains cable) is used on Pfeiffer OmniControl 200, 300, 400, and DCU 110 controllers, HiScroll dry scroll roughing/backing pumps, and with other Pfeiffer products. These power cords have a standard NEMA 5-15P 115 VAC plug one one end and an IEC320 C13 female socket connector on the other. This cable is 3 meters long (10 ft.) and has 18 gauge wire and 3 conductors (18/3).

Pfeiffer Part Number: PM 061 187-X. This Pfeiffer main power input cable connects a HiPace 1200 turbo pump directly to a 115 VAC single phase electrical source. The HiPace 1200 turbo pump has a Hastings HAN 3 type plug built into it. This 3 meter long cable has a mating HAN 3 connector one one end, and a standard NEMA 5-15P plug on the other. This power cable supplies power to the pump's integrated TC 1200 drive unit and to an (optional) OmniControl 001 controller (part number P1012626). This Pfeiffer mains input power cable for the HiPace 1200 turbo pump has part number PM 061 187-X.

Pfeiffer Part Number: P 4564 309 HB. This Pfeiffer main power input cable connects a HiPace 1200 turbo pump directly to a 208 VAC single phase electrical source. The HiPace 1200 turbo pump has a Hastings HAN 3 type plug built into it. This 3 meter long cable has a mating HAN 3 connector one one end, and a standard NEMA 6-15P plug on the other. This power cable supplies power to the pump's integrated TC 1200 drive unit and to an (optional) OmniControl 001 controller (part number P1012626). This Pfeiffer mains input power cable for the HiPace 1200 turbo pump has part number PM 061 187-X.

This special serial cable allows RS485 communications between a Pfeiffer HiPace turbo pump TC drive unit and a Pfeiffer OmniControl or DCU controller. This interface cable has 4-pin, M12, round screw-type connectors on both ends. This cable is 10 meters long (10 ft.) and meets or exceeds OEM specs (OEM PN: PM 061 285 -T). On TC 110 drive units, which have a 15-pin D-Sub (X3) connector, a power and communications adapter cable (part number P103335 or P1011168) is used to split out the X3 connector into a pump power cable and a short RS485 communication cable (terminated with an M12 connector). This 10 meter long RS485 cable attaches to and extends that short cable. The other end of this cable connects to the M12 round connector on an OmniControl or a DCU controller.

This special serial cable allows RS485 communications between a Pfeiffer HiPace turbo pump TC drive unit and a Pfeiffer OmniControl or DCU controller. This interface cable has 4-pin, M12, round screw-type connectors on both ends. This cable is 3 meters long (10 ft.) and meets or exceeds OEM specs (OEM PN: PM 061 283-T3). On TC 110 drive units, which have a 15-pin D-Sub (X3) connector, a power and communications adapter cable (part number P103335 or P1011168) is used to split out the X3 connector into a pump power cable and a short RS485 communication cable (terminated with an M12 connector). This 3 meter long RS485 cable attaches to and extends that short cable. The other end of this cable connects to the M12 round connector on an OmniControl or a DCU controller.

This Pfeiffer shielded relay box allows a backing pump to be controlled by the TC 400 or TC 1200 electronic drive unit on Pfeiffer HiPace turbo pumps. The box has a 0.45 meter long communication cable which connects directly to one of the TC drive unit's M12 accessory ports. This relay box can operate any single phase backing pump that has a starting current of up to 20A (the maximum relay contact load). This includes Pfeiffer HiScroll dry scroll and Duo series rotary vane pumps. This Pfeiffer backing pump shielded relay box has part number: PM 071 285-X. This box operates on 100-240 VAC, 50/60Hz. An appropriate AC mains input cable must be wired into the box, as well as an output cable to power the backing pump. Note that the backing pump voltage must be the same as the input power voltage.

This Pfeiffer fine inlet screen (0.8 mm mesh) with centering ring has a multifunctional coating for anti-twist protection. It is used to filter the vacuum flow and keep objects from being sucked into the HiPace 800 or 120 turbo pumps. This screen has an ISO-K/F 200 flange size. Depending on the gas used, some pump speed reduction will occur when using this screen. This fine screen centering ring has Pfeiffer part number PM 016 221 AU. This screen fits:HiPace 800 with ISO-K 200 flange, Pfeiffer pump part number: PM P04 300HiPace 1200 with ISO-F 200 flange, Pfeiffer pump part number: PM P06 001

This Pfeiffer fine inlet screen (0.8 mm mesh) is used to filter the vacuum flow and keep objects from being sucked into the HiPace 800 or 1200 turbo pumps. This screen has a CF 10.0" flange size. Depending on the gas used, some pump speed reduction will occur when using this screen. This fine screen centering ring has Pfeiffer part number: PM 016 321. This screen fits:HiPace 800 with Conflat CF 10.0" flange, Pfeiffer pump part number: PM P04 301HiPace 1200 with Conflat CF 10.0" flange, Pfeiffer pump part number: PM P06 002

Pfeiffer Part Number: PM Z01 291 B. This Pfeiffer venting valve for HiPace 300, 300C (chemical resistant), 350, 450, 700, and 800 turbo pumps with a TC 400 drive unit, and HiPace 1200 turbo pumps with a TC 1200 drive unit, screws into the G 1/8" (BSPP) vent port of the pump (sealing ring included). It ensures the controlled, automatic venting of the turbo pump after shutting down or in the event of a power failure, and limits an uncontrollable pressure rise rate in excess of the permissable maximum (15 hPa/s), thus preventing possible damage to the pump's rotor and magnetic bearing. This valve has an M12 electical connector that plugs directly into one of the accessory ports in the turbo pump's integrated TC 400 or TC 1200 drive unit. The TC drive unit controls and supplies power to the valve.The activation (control) of this valve for the venting connection is user configured and supported by Pfeiffer controllers (OmniControl 300, OmniControl 400, or OmniControl 001) or externally via RS485. This Pfeiffer venting valve for medium and large HiPace turbo pumps with integrated TC drive unit has part number PM Z01 291 B.

This Pfeiffer vacuum flange adapter can be used on all HiPace turbo pumps. It screws into the G 1/8" BSPP vent or sealing gas port on the pump (sealing ring included), and converts the port into a standard KF-10 flange for easy connection to the user's vacuum system. It can be used for connection to venting valves, sealing gas valves, power failure venting units, sealing gas throttles, etc. This vacuum flange adapter has Pfeiffer part number PM 033 737-T . This vacuum flange adapter fits the vent or gas sealing ports on all these Pfeiffer turbo pumps:HiPace 80HiPace 300HiPace 300CHiPace 350HiPace 450HiPace 700HiPace 800HiPace 1200

This Pfeiffer vacuum flange adapter can be used on all HiPace turbo pumps. It screws into the G 1/8" BSPP vent or sealing gas port on the pump (sealing ring included), and converts the port into a standard KF-16 flange for easy connection to the user's vacuum system. It can be used for connection to venting valves, sealing gas valves, power failure venting units, sealing gas throttles, etc. This vacuum flange adapter has Pfeiffer part number PM 016 780-T. This vacuum flange adapter fits the vent or gas sealing ports on all these Pfeiffer turbo pumps:HiPace 80HiPace 300HiPace 300CHiPace 350HiPace 450HiPace 700HiPace 800HiPace 1200