The Ideal Vacuum Air Admittance Vent Valve is Stainless Steel with an Aluminum, manually operated control knob attached to a screw actuated plunger. The plunger is sealed onto the valve seat in the valve body by a Viton O-ring. The Ideal Vacuum air admittance vent valve can also be pipeline mounted. These manual air admittance vent valves have a KF16 vacuum flange size and are sold as one each. Body: Stainless SteelO-ring seal: VitonMaximum leak rate across body: less than1 x 10 -7 mbar.ls-1Maximum leak rate across valve seat: less than1 x 10 -7 mbar.ls-1Weight: 100 gramsFitting: KF16, NW16A: Valve Height (Closed): 35.56 mm (1.4 in.)

Vent Valves are typically used to introduce air in to the vacuum chamber and bring the system up to atmospheric pressure. These vent valves can be used to fill the vacuum chamber with room air or a N2 gas supply can be plumbed to the 1/4 O.D. tube side of the valve. These vent valves have a NW-16 vacuum flange for connection to the vacuum system, are manually operated, and made of stainless steal.

Vent Valves are typically used to introduce air in to the vacuum chamber and bring the system up to atmospheric pressure. These vent valves can be used to fill the vacuum chamber with room air or a N2 gas supply can be plumbed to the 1/4 O.D. tube side of the valve. These vent valves have a NW-25 vacuum flange for connection to the vacuum system, are manually operated, and made of stainless steel.

Vent Valves are typically used to introduce air in to the vacuum chamber and bring the system up to atmospheric pressure. These vent valves can be used to fill the vacuum chamber with room air or a N2 gas supply can be plumbed to the 1/4 O.D. tube side of the valve. These vent valves have a NW-40 vacuum flange for connection to the vacuum system, are manually operated, and made of stainless steal.

This Pressure Relief Valve (PRV) from Accu-Glass is mounted on a CF 2.75" flange. Factory setting is at 2.0 psi, but with its' precise pressure adjustment can be set as low as 0.50psi. This PRV is suitable for High vacuum processes down to 1x10-8 Torr (leak tested to 5x10-10 Standard cc/sec of He), and has a temperature rating up to 150° C. Vacuum systems are only designed to operate under external (atmospheric) pressure. A Pressure Relief Valve offers a means of protecting vacuum vessels against internal over-pressurization. There are many scenarios in which rapid pressure buildup inside a vacuum vessel may occur — such as a runaway gas back-fill operation. Besides protecting delicate instruments and equipment, A Pressure Relief Valve also minimizes the risk of injury to system operators and other lab personnel.

These NEW Edwards IPV25MKS Manual Inline Lever Operation Bellows Isolation Valves are very quick acting. The LV10K needle valve provides fine control of gas bleed into a vacuum chamber or a regulated leak to control pressure in a vacuum system and is suitable for gas admission down to 10-5 mbar / 8 x 10-6 Torr. Maximum flow rate: (approx) 0.1 l s-1 Maximum inlet pressure: 2000 mbar / 1500 Torr Maximum leak rate across seat: 10-7 mbar l s-1 / 8 x 10-8 Torr l s -1 Maximum leak rate across body: 10-7 mbar l s-1 / 8 x 10-8 Torr l s -1 Vacuum connection: NW10 Weight: (g/oz) 138 / 4.8 Suitable for pipeline or panel mounting. These LV10K needle valves are primarily for vacuum processes. They are brand new.

The Edwards IPVA10EK is a solenoid operated vent valve designed for automatic admittance of air or vent gas into a vacuum system. The valve has two ports with KF 10, NW 10 flanges. One of the valve ports is connected to the vacuum system, the other port can be left open to atmosphere or connected to a vent gas supply. The vacuum system is isolated from atmosphere (or the vent gas supply) by a fluoroelastomer pad on the base of the valve plunger, which seals against the body of the valve. This is a normally closed version of the valve suitable for use with 110 VAC to suit your application. These Edwards IPVA10EK 110VAC air admittance vent valves have a KF10 vacuum flange and are sold as one each.

The Edwards IPVA10EK is a solenoid operated vent valve designed for automatic admittance of air or vent gas into a vacuum system. The valve has two ports with KF 10, NW 10 flanges. One of the valve ports is connected to the vacuum system, the other port can be left open to atmosphere or connected to a vent gas supply. The vacuum system is isolated from atmosphere (or the vent gas supply) by a fluoroelastomer pad on the base of the valve plunger, which seals against the body of the valve. This is a normally closed version of the valve suitable for use with 24 VDC to suit your application. These Edwards IPVA10EK 24 VDC air admittance vent valves have a KF10 vacuum flange and are sold as one each.

The Edwards IPVA10EK is a 24 VDC solenoid operated vent valve designed for automatic admittance of air or vent gas into a vacuum system. The valve has two ports with KF 10, NW 10 flanges. One of the valve ports is connected to the vacuum system, the other port can be left open to atmosphere or connected to a vent gas supply. The vacuum system is isolated from atmosphere (or the vent gas supply) by a fluoroelastomer pad on the base of the valve plunger, which seals against the body of the valve. This is a normally open (NO) version of the valve. The solenoid operates on 24VDC. These Edwards IPVA10EK 24 VDC air admittance vent valves have a KF10 vacuum flange and are sold as one each.