This Teledyne-Hastings DV-6M 1/8" NPT thermocouple (TC) vacuum gauge tube measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C.

This Teledyne-Hastings DV-6M 1/8" NPT thermocouple (TC) vacuum gauge tube measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C.

This Teledyne-Hastings DV-6M-KF-16 thermocouple (TC) vacuum gauge tube with KF16 fitting, measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C.

This Teledyne-Hastings DV-6M-KF-25 thermocouple (TC) vacuum gauge tube with KF25 fittin, measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C.

This Teledyne-Hastings DV-6M thermocouple (TC) vacuum gauge tube with 4-VCR fitting, measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C.

This Teledyne-Hastings DV-36 DV 6 series Thermocouple (TC) vacuum gauge tube measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as "rough" indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C.

Teledyne Hastings OM-25-OFV 25 ft. long extension cable for connecting controllers to vacuum gauges.

This Teledyne-Hastings DV-6M 1/8" NPT thermocouple (TC) vacuum gauge tube measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C.

PN: DV-6S Teledyne Hastings DV-6S ruggedized thermocouple vacuum gauge tubes have a rugged steel housing and can measure pressure between 0.001 and 1 Torr (1 to 1000 mTorr). Teledyne Hastings DV-6S vacuum sensors are calibrated for nitrogen or air, but conversion factors for other gases are available. The Teledyne Hasting DV-6S tubes are matched and interchangeable without calibration adjustments. The DV-6S thermocouple tubes are for use with Teledyne Hastings Digital or Analog VT-6 thermocouple gauge controllers. These DV-6S tubes have a standard 1/8 inch male NPT vacuum fitting are brand new with full Teledyne Hastings warranty. Part Number DV-6S. Thermocouple sensors (thermal conductivity gauges) rely on the fact that the ability of a gas to conduct heat decreases with pressure. In this type of gauge, a wire filament is heated by running current through it. A thermocouple or Resistance Temperature Detector (RTD) can then be used to measure the temperature of the filament. This temperature is dependent on the rate at which the filament loses heat to the surrounding gas, and therefore on the thermal conductivity. A common variant is the Pirani gauge which uses a single platinum filament as both the heated element and RTD. These gauges are accurate from 10 Torr to 10−3 Torr, but they are sensitive to the chemical composition of the gases being measured (from Wikipedia.org).

PN: DB-20, NIST-DV-6M The Teledyne Hastings Instruments (THI) DB-20 Reference Tube is an evacuated, sealed vacuum gauge tube accurately calibrated to precisely simulate a gauge tube at a given operating pressure. This Teledyne Hastings Instruments DB-20 Reference Tube it is electrically equivalent to the Gauge Tube DV-6M series Range 0-1000 mTorr, used with THI instruments. The DB-20 Reference Tube permits quick and easy recalibration of THI Vacuum Gauge Indicators by merely plugging the instrument into the reference and adjusting the calibration “current set” potentiometer until the instrument reads the exact pressure noted on the reference. THI Reference Tubes are available equivalent to most THI Gauge Tubes. Part Number DB-20.

These Teledyne Hastings Digital VT thermocouple vacuum gauge controllers are matched for the DV-6 thermocouple vacuum gauge tubes (Stock Number 55-288DV6, Operates on 115 VAC). They measure pressure between the range of 0.001 and 1 Torr (1 to 1000 mTorr). The Teledyne Hastings Digital VT thermocouple controllers are self-contained instruments that offer extreme versatility for most vacuum applications. The electronic design assures long life and minimal maintenance. Compact Digital VT Models are ready for mounting onto a panel. Teledyne Hasting thermocouple tubes are also available but sold separately.

The Teledyne Hastings Instrument’s Digital DCVT, is a digital readout version of the successful CVT Series. These pressure gauges offer exceptional stability, accuracy, and reliability. This instrument has been designed for laboratory or light industrial applications. It is not suitable for outdoor or heavy industrial areas where spraying liquid or wash-downs may occur. A precision A/D converter, with a microprocessor is used to measure the gauge tube’s signal output; it converts the measurement to a pressure reading using the gauge tube’s well defined output/pressure function, and then displays the result. A 0 – 1 volt amplified non-linear gauge tube output version along with 0-1volt, 0-5volt, 0-10volt, 0-20mA, and 4-20mA linear gauge tube output versions are available on the back panel. This unit accepts 90-250 VAC for input power.

These Teledyne Hastings Digital DCVT-6 Controllers are used with DV-6 Tubes, Digital Output (DCVT) Ranges 1 - 999 mTorr Dual Setpoint Control Relays. The digital DCVT-6 Vacuum Measurement is the new generation series and replaces the obsolete Analog CVT thermocouple vacuum gauge controllers are matched for the DV-6 thermocouple vacuum gauge tubes (Stock Number VT-26-X-Y). They measure pressure between the range of 0.001 and 1 Torr. The Teledyne Hastings Analog CVT thermocouple controllers are self-contained instruments that offer extreme versatility for most vacuum applications. The electronic design assures long life and minimal maintenance. These controllers digital DCVT Models are ready for mounting onto a panel. Teledyne Hasting thermocouple tubes are also available but sold separately.

This Teledyne-Hastings model VT-6A (formerly VT-6-X-Y) panel mount gauge controller for DV-6 thermocouple vacuum tube gauges measures between 0 and 1000 mTorr, and operates on 115/230 VAC. A removeable round rear cover provides access to the AC power, gauge tube, and output terminals (0-1 VDC analog, non-linear). Includes gauge cable. Please see the Gauge Controller manual in the downloads for specs and information. Thermocouple tubes and AC power cable sold separately.

This Teledyne-Hastings model VT-6AB (VT-6B-X-Y) enclosed cabinet gauge controller for DV-6 thermocouple vacuum tube gauges controllers measures between 0 and 1000 mTorr, and operates on 115 VAC. This model has connected power and gauge tube cables. It also features BNC connectors on the back for output (0-1 VDC analog, non-linear). Please see the Gauge Controller manual in the downloads for specs and information. Thermocouple tubes are sold separately.

This Teledyne-Hastings model VT-6S5-X-Y enclosed cabinet gauge controller for VT6 thermocouple vacuum tube gauges controllers measures between 0 and 1000 mTorr, and operates on 115 VAC (connected power cable). This model can be connected to 5 gauge tubes and has a 5 position switch on the face for selection. This controller also has BNC connectors on the back for output (0-1 VDC analog, non-linear). Please see the Gauge Controller manual in the downloads for specs and information. Thermocouple tubes and gauge tube cables are sold separately.

These Teledyne Hastings Analog CVT26A (panel mount) thermocouple vacuum gauge controllers are matched for the DV-6 thermocouple vacuum gauge tubes and operate on 115VAC. They measure pressure between the range of 0-1000 mTorr . The Teledyne Hastings Analog CVT26A thermocouple controllers are self-contained instruments that offer extreme versatility for most vacuum applications. The electronic design assures long life and minimal maintenance. They are fully automatic, continuous-reading instruments for unlimited vacuum applications. These controllers have 2 set points that are durable and have 5 amp single pole double throw relays which can be configured normally open or normally closed.

This is a replacement octal socket for all Teledyne-Hastings thermocouple vacuum gauge tubes including all DV-4, DV-5, DV-6 and DV-23 gauges. Use to replace a broken part, or to make your own gauge cable. We stock most Teledyne Hastings thermoucouple gauge tubes and gauge controllers.

The Teledyne Hastings Instruments’ DAVC (Digital AVC) is a microprocessorbased vacuum gauge. In addition to the linear analog outputs (0-1 VDC, 0-5 VDC, 0-10 VDC, 4-20 mA, or 0-20 mA), pressure measurements can be accessed via the RS232 digital output. Digital readings can be provided in either Torr, mbar, or Pascal units. A precision A/D converter, along with the microprocessor, measures the thermocouple vacuum gauge tube’s output and converts the measurement to a pressure reading employing the gauge tube’s well-defined output/ pressure function. The DAVC is a continuous-reading instrument for vacuum measurement and process control applications. The instrument is packaged in a small aluminum case with controls and electrical “D” connector located on the top.

This is a replacement AC power cord for all enclosed analog Teledyne-Hastings thermocouple vacuum gauge controllers. We stock most Teledyne Hastings thermoucouple gauge tubes, reference tubes, and gauge controllers.

This is a replacement octal socket cable 8 ft. for all Teledyne-Hastings thermocouple vacuum gauge tubes including all DV-4, DV-5, DV-6 and DV-23 gauges. We stock most Teledyne Hastings thermoucouple gauge tubes and gauge controllers.